Takaisin blogiin
Ohjeet 2026-11-16 vapordna 0 katselukertaa

Stubby Panel Set for Stubby AIO: Install Without Scratches

Stubby Panel Set for Stubby AIO: Install Without Scratches

A practical walkthrough for swapping the clear acrylic panels on your 18650 Stubby AIO, with fit checks and scratch-free handling habits.

Confirm the fit before you touch a panel

The Stubby Panel Set for Stubby AIO is made for one device only: the 18650 Stubby. It will not work with the Stubby 21. Check your device before ordering or prying anything loose, because a set that does not fit invites the exact scratches and cracked edges you are trying to avoid.

The set includes three acrylic pieces: a battery panel, an interface panel, and a faceplate panel. The interface panel has cutouts for the screen and adjustment buttons, so the buttons sit recessed but remain accessible without removing the panel. The faceplate uses an hourglass airflow design to feed your bridge or tank.

What the Stubby Panel Set includes

  • Stubby Panel Set for Stubby AIO: Clear Outer Panel Set for the Stubby AIO by Orca Vape includes a battery panel, interface panel, and faceplate panel made from acrylic. Knowing there are three separate pieces helps you plan removal and reinstallation one panel at a time instead of handling the whole set at once.
    Stubby Panel Set for Stubby AIO
    Stubby Panel Set for Stubby AIO
  • Stubby Panel Set for Stubby AIO: Only for the 18650 Stubby and will not work with the Stubby 21. This is the compatibility line that decides whether the set is worth opening at all.

A scratch-conscious removal and install sequence

The supplied information does not include a manufacturer removal procedure, screw torque, or tool list. Treat the steps below as handling habits built around the acrylic panels and the cutouts described in the product record, not as an official service manual.

  1. Work over a soft, clear surface: A microfiber cloth or clean mat keeps acrylic from sliding against grit. Small particles trapped under a panel are a common source of fine scratches.
  2. Remove one panel at a time: Separate the battery, interface, and faceplate panels as you go. Laying all three loose at once makes it easy to stack them face-down or knock them together.
  3. Lift from an edge, not the center: Acrylic flexes. Prying near the middle of a panel concentrates stress; working an edge gives you more control. Use a fingernail or a non-marring plastic tool rather than a metal driver.
  4. Keep the interface panel oriented to its cutouts: The screen and adjustment button cutouts only line up one way. Test-fit the interface panel dry before pressing it into place so you are not sliding it around against the device.
  5. Seat the faceplate with the airflow design in mind: The hourglass airflow design needs to sit flush against the bridge or tank opening. If the panel rocks, stop and check alignment rather than forcing it down.
  6. Wipe before you finish: A dry microfiber pass on both the panel and the device surface removes dust before the final seat. Avoid paper towels, which can leave lint and abrasive edges.

Habits that keep acrylic panels clear

  • Store spare panels flat: Acrylic can warp or scratch when kept loose in a pocket or drawer with keys and coins. Keep the unused finish in a soft pouch.
  • Clean with mild soap and water: The supplied information does not name a cleaning agent. A mild soap-and-water wipe followed by a microfiber dry is a conservative default for acrylic; avoid alcohol-heavy cleaners unless the maker confirms them.
  • Do not overtighten around the panels: The record does not give a torque figure. Tighten until the panel sits flush and stop; extra force is more likely to crack acrylic than to improve the seal.
  • Check the buttons after the interface panel is on: The adjustment buttons are meant to stay recessed but accessible. If a button feels stuck, lift the panel and reseat it rather than pressing harder.

Frosted Clear or Frosted Smoke: choosing a finish

Both finishes use the same three-panel layout and the same 18650 Stubby compatibility. The choice is visual, not functional.

  • Frosted Clear: A cleaner, more transparent look that shows the device underneath. Fine scratches tend to be less obvious on frosted surfaces than on fully clear ones.
  • Frosted Smoke: A darker tint that hides smudges and internal wear. It also changes how the screen and button cutouts read visually.

When the panel does not sit right

Stop before adding force. Recheck that you have the 18650 Stubby and not the Stubby 21, that the interface panel cutouts are aligned with the screen and buttons, and that no old panel fragment or debris is trapped underneath. If the faceplate still rocks, remove it and inspect the airflow opening for a misaligned bridge or tank.

The supplied information does not confirm replacement screws, torque values, or a warranty process for damaged acrylic. If a panel cracks during fitting, contact the retailer rather than continuing to install it.

Aiheeseen liittyvät artikkelit

Customer Service
Koti
Tuotteet
Ostoskori
Profiili